13 Things Your Electrician Wants You to Know

-Dan Stout

Almost every home uses electric service to one degree or another. And sooner or later, something is going to go wrong with your home’s electrical system. Whether you’re looking to add a light fixture or run rough electric for an addition, here are a few key facts that your electrician wishes you knew.

Don’t Ignore Warning Signs
The most important thing any electrician wants you to do is to never, ever ignore the warning signs that indicate problems in your electrical system. Whether it’s a popping noise from an outlet, a light
switch that runs extremely hot, or a breaker that won’t reset, when you have an electrical issue, it’s important that you take it seriously.

Luckily, most electrical issues can be resolved relatively quickly, as long as they are not allowed to fester and become an increasing hazard over time. There’s a reason that awareness of electrical issues is a key step in preventing fires in the home.

Understand GFCI
One of the most common service calls electricians get is about what appears to be a failure in a bathroom circuit. By code, all outlets within 6 feet of a water source are required to be protected by a ground fault circuit interrupt (GFCI). These are important safety devices that cut off power if a circuit
is losing amperage, so GFCIs are most commonly seen in bathrooms and exterior outlets. The thing that your electrician wants you to remember is that a single GFCI device protects everything else “downstream” on that circuit. Because bathrooms are often not on an isolated circuit, that means a triggered GFCI will kill the power to outlets and lights that may seem unrelated. And things can be even more confusing when the GFCI is installed at the electrical breaker box itself.

This service call is especially common for outdoor circuits and in homes where multiple bathrooms are on a single circuit, and it’s the reason that checking the GFCI is an important part of troubleshooting dead outlets.

Overhead Power Lines are Live!
Overhead lines are normally NOT insulated. When you see birds or squirrels on them, they are only
alive because they aren’t completing a circuit by touching the ground or offering the current an easier path than following the cable itself.

Most of the outdoor power lines you see are weather coated at most, with no insulation other than spacers at utility poles. Because they are so high above the ground, this isn’t an issue unless the lines fall, or a worker comes into contact with them while trimming a tree. And while lines that could be touched from a rooftop or tree are insulated, that insulation degrades over time, eventually crumbling and revealing bare wire. Approach all overhead lines with full knowledge of what they are potentially fatal objects best left to a licensed electrician or utility worker.

Know Your DIY limits
The DIY mind-set is wonderful thing. It’s a great way to learn about your home and develop your skills and self-reliance. But, it’s just as important to know the boundaries and limitations of your
skills. If you are a DIY newbie, a good rule of thumb is to only work on electrical components that are outside of the wall. As you develop your skills as an amateur electrician, you can do more advanced work, including fishing cable and adding outlets (so long as your local building department allows it). The problem arises when DIY enthusiasts who have more enthusiasm than experience tackle an electrical project, and then bury their less than perfect work behind a layer of drywall.

Working with wiring outdoors is a great intermediate step, since much of the work is easily accessed during the troubleshooting stage.

White Isn’t Always Neutral, and Black Isn’t Always Live
We know, this is contradicting best practices, but what your electrician understands is that a home’s electrical system is large, complicated, and may have been worked on by dozens of different people
, many of whom may not have been properly trained or following code. The end result is that when you open up an electrical outlet you may find a bewildering bird’s nest of wires, electrical tape and wire nuts. That doesn’t mean you can’t work on it, but it does mean that you need to be very careful and not make assumptions. Always use a non-contact voltage tester to verify that a line is dead before working on it. Here’s how.

If you need a reminder about how bad some amateur electrical can be, check out this list of the most common electrical code violations.

Low Voltage Doesn’t Mean No Danger
We’re not going to try to tell you that a low-voltage system is as dangerous as working on your electrical breaker box. But electricians want you to know that you should still take basic precautions. Treat low-voltage wiring as though it were standard, and you will pick up best practices that will pay off when working in higher voltage situations. Also, your electrician would be quick to remind you that it’s not the voltage that is harmful, but the current. Sometimes even low-voltage wiring can draw a higher than safe current.

A more common hazard when working with low-voltage wiring involves receiving a mild shock that surprises the installer and causes them to fall from a ladder or step stool. And, last but not least, keep in mind the importance of securing connections! A spark from a poorly secured low-voltage connection will ignite combustible materials just as easily as that from a 110v junction. Avoiding this hazard can be as simple as doing the job right, and not doing something as foolish as storing your oily rags next to a low-voltage device.

Vampires are Real!
Well, okay: vampire draws are real. Unlike Count Dracula, these items don’t drain your blood, but they will suck dollars out of your wallet. Electrical devices that have a “standby” mode and things
that use remote controls always need to maintain a steady stream of power in order to wake up quickly. In addition, charging devices, such as phone chargers and laptop chargers, draw power even when not plugged into their device. When electricians get calls about high energy bills, “vampire” devices are often the first thing they look at as potential culprits.

Protective Gear is only Protective if it’s Properly Made
Many people know that rubber is a great insulator, and so sometimes DIYers wrap themselves in rubber boots and gloves before tackling electrical issues that make them nervous. The problem is that most household robber isn’t pure. In order to keep the price
down, manufacturers mix in additives that lower the cost and increase durability. If you’re relying on rubber to keep you safe from an electrical charge, make sure you’re using actual safety gear.

Have you ever seen a TV show of film where an electrical line falls on a car, but the passengers are safe? That’s actually accurate, but not because the tires are insulating the vehicle. It’s because the tires are such good conductors that the electricity takes the path of least resistance, traveling to the ground through the tires and bypassing the interior completely.

Take a tip from your electrician, and make quality insulators part of your standard kit of protective gear.

You Can’t Install a Three-Slot receptacle Without a Ground Wire
If you have two-slot outlets, it’s tempting to replace them with three-slot outlets so you can plug in
three-prong plugs. But don’t do this unless you’re sure there’s a ground available. Use a tester to see if your outlet is grounded. A series of lights indicates whether the outlet is wired correctly or what fault exists. These testers are readily available at home centers and hardware stores.

If you discover a three-slot outlet in an ungrounded box, the easiest fix is to simply replace it with a two-slot outlet as shown. Dead outlet?

NEVER Tape or Hold Down a Circuit Breaker
Ask any electrician, and they can tell you: circuit breakers work because they break the circuit! When
a breaker keeps popping, you have to find and fix the problem. If you hold a breaker down with tape, then the dangerous conditions will only continue, and you’ll be setting yourself up for a major problem. Forcing the breaker to maintain contact is a recipe for disaster, and should be avoided at all costs.

If you, a friend or family member doesn’t know how to reset a circuit breaker, here’s a great tutorial everyone should read.

You Should Definitely Consider Tamper-Resistant Receptacles
Tamper-resistant receptacles are designed to stop a kid from inserting an object, such as a paper clip.
They’re required for all locations, indoors and out. Tamper-resistant receptacles are a great invention, so use them — it’s national electric code. We’ll show you how to correctly install a tamper-resistant outlet.

Outdoor Receptacle Covers Matter
On outdoor receptacles, flat covers provide protection only when a receptacle isn’t in use, but it’s not uncommon for extension cords to be plugged in for extended periods of time; for holiday lights, for example. In-use or “bubble covers” provide protection at all times. The national electrical code defines a “wet location” as an area that is subject to saturation with water
or other liquids, and unprotected locations exposed to the weather. The national electric code has another definition for “damp locations” that is more subjective, but if you think the receptacle is going to get wet, use an in-use cover. And don’t forget the weather-resistant receptacle. The national electric code requires that all 15- and 20-amp receptacles be rated as weather-resistant and tamper-resistant when installed in both wet and damp locations. Learn How to install outdoor lighting and an outlet here.


Many of these tips are cautionary tales. But they’re not intended to scare you away! The fact is, many electricians are eager to encourage homeowners to learn how to do basic electrical work on their own.


Call ON-LINE Electric TODAY ! (813) 662-0362